6AG2136-6AB00-1CA1

24 V encoder supply
Output current, max	300mA; total current of all encoders/channels
Short-circuit protection	Yes

24 V encoder supply
24 V	Yes; min. L+ (-1.5 V)

Address space per module
Outputs	5byte; S7-300/400F CPU, 4 byte

Address space per module
Inputs	14byte; S7-300/400F CPU, 13 byte

Alarms
Limit value alarm	No

Alarms
Diagnostic alarm	Yes

Altitude during operation relating to sea level
Ambient air temperature-barometric pressure-altitude	Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m)

Altitude during operation relating to sea level
Installation altitude above sea level, max	2000m

Ambient temperature during operation
horizontal installation, max	60C; = Tmax; +70 C for 10 min (OT1, ST1/ST2 acc. to EN 50155); +70 C continuously with configured slots to the left and right of the module (OT3, ST1/ST2 acc. to EN 50155)

Ambient temperature during operation
horizontal installation, min	-30C; = Tmin (incl. condensation/frost)
vertical installation, min	-30C; = Tmin

Ambient temperature during operation
vertical installation, max	50C; = Tmax

Analog inputs
For current measurement

Analog inputs
Number of analog inputs	4

Analog value generation for the inputs
Measurement principle	Sigma Delta

Automatic encoding
Electronic coding element type F

Cable length
shielded, max	200m

CiR - Configuration in RUN
Calibration possible in RUN	No
Reparameterization possible in RUN	No

Common mode voltage, max
Common mode interference, min	70dB

Conformal coating
Coatings for printed circuit board assemblies acc. to EN 61086	Yes; Class 2 for high reliability
Military testing according to MIL-I-46058C, Amendment 7	Yes; Discoloration of coating possible during service life
Protection against fouling acc. to EN 60664-3	Yes; Type 1 protection

Conformal coating
Electronic equipment on rolling stock acc. to EN 50155	Yes; Class PC2 protective coating acc. to EN 50155:2017

Conformal coating
Qualification and Performance of Electrical Insulating Compound	Yes; Conformal coating, Class A

Coolants and lubricants
Resistant to commercially available coolants and lubricants	Yes; Incl. diesel and oil droplets in the air

Diagnoses
Wire-break	Yes

Diagnoses
Monitoring the supply voltage	Yes

Diagnoses
Short-circuit

Diagnostics indication LED
for channel diagnostics	Yes; red LED
Monitoring of the supply voltage (PWR-LED)	Yes; green PWR LED
RUN LED	Yes; green LED

Diagnostics indication LED
ERROR LED	Yes; red LED

Diagnostics indication LED
Channel status display	Yes; green LED
for module diagnostics	Yes; green/red DIAG LED

Dimensions
Depth	58mm
Height	73mm
Width	15mm

Errors/accuracies
Temperature error (relative to input range), (+/-)	0.023%/K

Errors/accuracies
Repeat accuracy in steady state at 25 C (relative to input range	0.1%

Errors/accuracies
Linearity error (relative to input range), (+/-)	0.1%

Firmware version
Color code for module-specific color identification plate	CC00
FW update possible	Yes
usable BaseUnits	BU type A0, A1

for voltage measurement
Burden of 2-wire transmitter, max
for current measurement as 2-wire transducer
for current measurement as 4-wire transducer

General information
Product type designation	F-AI 4XU 0..10V HF

Highest safety class achievable in safety mode
Category according to ISO 13849-1	Cat. 4

Highest safety class achievable in safety mode
SIL in accordance with EN 50126, 50128, 50129	SIL 2; a higher safety integrity level is possible if tested and approved for the specific application under consideration of all local regulations

Highest safety class achievable in safety mode
Performance level according to ISO 13849-1	PLe
SIL acc. to IEC 61508	SIL 3

Input current
Current consumption (rated value)	0.38A
Current consumption, max	0.4A

Input ranges (rated values), currents
4 mA to 20 mA

Input ranges (rated values), currents
Input resistance (0 to 20 mA)
Input resistance (4 mA to 20 mA)

Input ranges (rated values), currents
0 to 20 mA

Integration and conversion time/resolution per channel
Interference voltage suppression for interference frequency f1 i	50 / 60 Hz

Integration and conversion time/resolution per channel
Integration time (ms)	20 / 16,667

Integration and conversion time/resolution per channel
Integration time, parameterizable	Yes
Resolution with overrange (bit including sign), max	16bit

Interference voltage suppression for f = n x (f1 +/- 1 %), f1 =
Series mode interference (peak value of interference < rated	40dB

Interrupts/diagnostics/status information
Diagnostics function	Yes

Isolation
Isolation tested with	750 V DC (type test) and according to EN 50155 (routine test)

Other
Note:	for use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A, Online Support article 109736776

permissible input voltage for voltage input (destruction limit),
permissible input current for current input (destruction limit),

Permissible potential difference
between the inputs (UCM)	10 Vpp

Potential separation channels
between the channels	No
between the channels and backplane bus	Yes
between the channels and the power supply of the electronics	Yes

Power
Power available from the backplane bus	70mW

Power loss
Power loss, typ	2W

Probability of failure (for service life of 20 years and repair
High demand/continuous mode: PFH in accordance with SIL3	< 1.00E-09 1/h
Low demand mode: PFDavg in accordance with SIL3	< 5.00E-05

Product function
I&M data	Yes; I&M0 to I&M3

Railway application
EN 50121-3-2	Yes; EMC for rail vehicles
EN 50124-1	Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC
EN 50125-2	Yes; Stationary electrical equipment - see ambient conditions
Fire protection acc. to EN 45545-2	Yes; For proof of conformity, see Service & Support

Railway application
EN 50125-1	Yes; Rail vehicles - see ambient conditions
EN 50125-3	Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)
EN 61373	Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B

Railway application
EN 50121-4	Yes; EMC for signal and telecommunications systems
EN 50155	Yes; Rail vehicles - temperature class OT1, ST1/ST2, horizontal mounting position

Relative humidity
With condensation, tested in accordance with IEC 60068-2-38, max	100%; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation

Remark
Note regarding classification of environmental conditions acc. t	* The supplied plug covers must remain in place over the unused interfaces during operation!

Smoothing of measured values
Number of smoothing levels	7

Smoothing of measured values
parameterizable	Yes
Step: High	Yes; 32x / 64x conversion cycle time
Step: low	Yes; 2x / 4x conversion cycle time
Step: Medium	Yes; 8x / 16x conversion cycle time
Step: None	Yes; 1x conversion cycle time

Supply voltage
permissible range, lower limit (DC)	19.2V
permissible range, upper limit (DC)	28.8V
Rated value (DC)	24V

Supply voltage
Reverse polarity protection	Yes

Usage in industrial process technology
Against chemically active substances acc. to EN 60654-4	Yes; Class 3 (excluding trichlorethylene)
Environmental conditions for process, measuring and control syst	Yes; Level GX group A/B (excluding trichlorethylene; harmful gas concentrations up to the limits of EN 60721-3-3 class 3C4 permissible); level LC3 (salt spray) and level LB3 (oil)

Use in stationary industrial systems
Against mechanical environmental conditions acc. to EN 60721-3-3	Yes; Class 3M8 using the SIPLUS Mounting Kit ET 200SP (6AG1193-6AA00-0AA0)
to biologically active substances according to EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
to chemically active substances according to EN 60721-3-3	Yes; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); *
to mechanically active substances according to EN 60721-3-3	Yes; Class 3S4 incl. sand, dust, *

Use on land craft, rail vehicles and special-purpose vehicles
Against mechanical environmental conditions acc. to EN 60721-3-5	Yes; Class 5M2 using the SIPLUS Mounting Kit ET 200SP (6AG1193-6AA00-0AA0)
against mechanical environmental conditions in agriculture acc.	Yes; level 1 (Location LE) using the SIPLUS Mounting Kit ET 200SP (6AG1193-6AA00-0AA0)
to biologically active substances according to EN 60721-3-5	Yes; Class 5B2 mold, fungus and dry rot spores (with the exception of fauna); Class 5B3 on request
to chemically active substances according to EN 60721-3-5	Yes; Class 5C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); *
to mechanically active substances according to EN 60721-3-5	Yes; Class 5S3 incl. sand, dust; *

Voltage, relative to input range, (+/-)
Current, relative to input range, (+/-)

Weights
Weight, approx	48g