6ES7511-1CK01-0AB0

24 V encoder supply
24 V	Yes; L+ (-0.8 V)

24 V encoder supply
Output current, max	1A
Short-circuit protection	Yes

Access protection
Protection level: Complete protection	Yes
Protection level: Read/write protection	Yes
Protection level: Write protection	Yes
protection of confidential configuration data	Yes

Access protection
Password for display	Yes

Accuracy
Cycle duration measurement	100 ppm; depending on measuring interval and signal evaluation
Frequency measurement	100 ppm; depending on measuring interval and signal evaluation
Velocity measurement	100 ppm; depending on measuring interval and signal evaluation

Address area
Number of IO modules	1024; max. number of modules / submodules

Alarms
Diagnostic alarm	Yes

Alarms
Hardware interrupt	Yes

Altitude during operation relating to sea level
Installation altitude above sea level, max	5000m; Restrictions for installation altitudes > 2 000 m, see manual

Ambient temperature during operation
horizontal installation, max	60C; note derating data for onboard I/O in the manual. Display: 50 C, at an operating temperature of typically 50 C, the display is switched off

Ambient temperature during operation
vertical installation, max	40C; note derating data for onboard I/O in the manual. Display: 40 C, at an operating temperature of typically 40 C, the display is switched off

Ambient temperature during operation
horizontal installation, min	-25C; No condensation
vertical installation, min	-25C; No condensation

Ambient temperature during storage/transportation
max	70C
min	-40C

Analog inputs
Number of analog inputs	5; 4x for U/I, 1x for R/RTD

Analog inputs
Technical unit for temperature measurement adjustable	Yes; C/F/K

Analog inputs
For current measurement	4; max
For resistance/resistance thermometer measurement	1

Analog inputs
For voltage measurement	4; max

Analog inputs
Cycle time (all channels), min	1ms; Dependent on the parameterized interference frequency suppression; for details, see conversion procedure in manual

Analog inputs
permissible input current for current input (destruction limit),	40mA
permissible input voltage for voltage input (destruction limit),	28.8V

Analog outputs
Cycle time (all channels), min	1ms; Dependent on the parameterized interference frequency suppression; for details, see conversion procedure in manual
Voltage output, short-circuit protection	Yes

Analog outputs
integrated channels (AO)	2

Backup
maintenance-free	Yes

Basic error limit (operational limit at 25 C)
Current, relative to input range, (+/-)	0.2%
Current, relative to output range, (+/-)	0.2%
Resistance thermometer, relative to input range, (+/-)	Pt100 Standard:
Resistance, relative to input range, (+/-)	0.2%
Voltage, relative to input range, (+/-)	0.2%
Voltage, relative to output range, (+/-)	0.2%

Cable length
shielded, max	200m
unshielded, max	600m; for technological functions: No

Clock
Backup time	6wk; At 40 C ambient temperature, typically
Deviation per day, max	10s; Typ.: 2 s

Clock
Type	Hardware clock

Clock synchronization
in AS, master	Yes
in AS, slave	Yes
on Ethernet via NTP	Yes

Clock synchronization
supported	Yes

Comparator
Can be changed from user program	Yes
Direction dependency	Yes
Number of comparators	2; per count channel; see manual for details

Configuration control
via dataset	Yes

Connectable encoders
2-wire sensor	Yes

Connectable encoders
permissible quiescent current (2-wire sensor), max	1.5mA

Connection of signal encoders
for current measurement as 4-wire transducer	Yes
for resistance measurement with four-wire connection	Yes
for resistance measurement with three-wire connection	Yes
for resistance measurement with two-wire connection	Yes
for voltage measurement	Yes

Control elements
Mode buttons	2
Number of keys	8

Controller
PID-Temp	Yes; PID controller with integrated optimization for temperature
PID_3Step	Yes; PID controller with integrated optimization for valves
PID_Compact	Yes; Universal PID controller with integrated optimization

Counting and measuring
High-speed counter	Yes

Counting functions
Counter response parameterizable	Yes
Software gate	Yes
Synchronization via digital input	Yes

Counting functions
Continuous counting	Yes
Counting range, parameterizable	Yes
Event-controlled stop	Yes
Hardware gate via digital input	Yes

CPU processing times
for bit operations, typ	60ns
for floating point arithmetic, typ	384ns
for word operations, typ	72ns

CPU processing times
for fixed point arithmetic, typ	96ns

CPU-blocks
Number of elements (total)	4000; Blocks (OB, FB, FC, DB) and UDTs

Data areas and their retentivity
Retentive data area (incl. timers, counters, flags), max	128kbyte; In total; available retentive memory for bit memories, timers, counters, DBs, and technology data (axes): 88 KB

Data areas and their retentivity
Extended retentive data area (incl. timers, counters, flags), ma	1Mbyte; When using PS 6 0W 24/48/60 V DC HF

Data blocks
Retentivity preset	No

Data blocks
Retentivity adjustable	Yes

DB
Number range	1 ... 60 999; subdivided into: number range that can be used by the user: 1 ... 59 999, and number range of DBs created via SFC 86: 60 000 ... 60 999
Size, max	1Mbyte; For DBs with absolute addressing, the max. size is 64 KB

Diagnoses
Wire-break	Yes; for analog inputs/outputs, see description in manual

Diagnoses
Monitoring the supply voltage	Yes

Diagnoses
Short-circuit	Yes; for analog outputs, see description in manual

Diagnoses
A/B transition error at incremental encoder	Yes

Diagnostic buffer
present	Yes

Diagnostic buffer
Number of entries, max	1000

Diagnostic buffer
of which powerfail-proof	500

Diagnostics indication LED
ERROR LED	Yes

Diagnostics indication LED
MAINT LED	Yes
RUN/STOP LED	Yes

Diagnostics indication LED
Channel status display	Yes

Diagnostics indication LED
Connection display LINK TX/RX	Yes
STOP ACTIVE LED	Yes

Diagnostics indication LED
for channel diagnostics	Yes; For analog inputs/outputs
Monitoring of the supply voltage (PWR-LED)	Yes

Digital input functions, parameterizable
Capture	Yes

Digital input functions, parameterizable
Gate start/stop	Yes

Digital input functions, parameterizable
Synchronization	Yes

Digital inputs
Source/sink input	P-reading

Digital inputs
from load voltage L+ (without load), max	20mA; per group

Digital inputs
Digital inputs, parameterizable	Yes
Input characteristic curve in accordance with IEC 61131, type 3	Yes

Digital inputs
integrated channels (DI)	16

Digital output functions, parameterizable
PWM output	Yes

Digital output functions, parameterizable
Switching tripped by comparison values	Yes; As output signal of a high-speed counter

Digital output functions, parameterizable
Cycle duration, parameterizable	Yes
Frequency output	Yes
Number, max	4
ON period, max	100%
ON period, min	0%
Resolution of the duty cycle	0.0036%; For S7 analog format, min. 40 ns

Digital outputs
Type of digital output	Transistor

Digital outputs
Controlling a digital input	Yes
Short-circuit protection	Yes; electronic/thermal

Digital outputs
Limitation of inductive shutdown voltage to	-0.8 V

Digital outputs
from load voltage L+, max	30mA; Per group, without load

Digital outputs
Current-sourcing	Yes; Push-pull output
Response threshold, typ	1.6 A with standard output, 0.5 A with high-speed output; see manual for details

Digital outputs
integrated channels (DO)	16
minimum pulse duration	2

Digital outputs
Accuracy of pulse duration	Up to

Dimensions
Depth	129mm
Height	147mm
Width	85mm

Display
Screen diagonal [cm]	3.45cm

Encoder signals, incremental encoder (asymmetrical)
Input frequency, max	100kHz
pulse encoder with direction	Yes
Signal filter, parameterizable	Yes

Encoder signals, incremental encoder (asymmetrical)
pulse encoder	Yes

Encoder signals, incremental encoder (asymmetrical)
Input voltage	24 V

Encoder signals, incremental encoder (asymmetrical)
pulse encoder with one impulse signal per count direction	Yes

Encoder signals, incremental encoder (asymmetrical)
Counting frequency, max	400kHz; with quadruple evaluation
Incremental encoder with A/B tracks, 90 phase offset	Yes
Incremental encoder with A/B tracks, 90 phase offset and zero tr	Yes

Encoder supply
Number of outputs	1; One common 24 V encoder supply

Engineering with
STEP 7 TIA Portal configurable/integrated from version	V17 (FW V2.9) / V15 (FW V2.5) or higher; with older TIA Portal versions configurable as 6ES7511-1CK00-0AB0

Errors/accuracies
Temperature error (relative to input range), (+/-)	0.005%/K
Temperature error (relative to output range), (+/-)	0.005%/K

Errors/accuracies
Crosstalk between the outputs, max	-80dB
Linearity error (relative to output range), (+/-)	0.15%

Errors/accuracies
Crosstalk between the inputs, max	-60dB
Linearity error (relative to input range), (+/-)	0.1%

Errors/accuracies
Output ripple (relative to output range, bandwidth 0 to 50 kHz),	0.02%
Repeat accuracy in steady state at 25 C (relative to input range	0.05%
Repeat accuracy in steady state at 25 C (relative to output rang	0.05%

FB
Number range	0 ... 65 535
Size, max	175kbyte

FC
Size, max	175kbyte

FC
Number range	0 ... 65 535

Flag
Size, max	16kbyte

Flag
Number of clock memories	8; 8 clock memory bit, grouped into one clock memory byte

for interrupt inputs
parameterizable	Yes; Same as for standard inputs

for standard inputs
at "0" to "1", max	20ms
at "0" to "1", min	4
at "1" to "0", max	20ms
at "1" to "0", min	4
parameterizable	Yes; none / 0.05 / 0.1 / 0.4 / 1.6 / 3.2 / 12.8 / 20 ms

for technological functions
Current per channel, max	0.5A; see additional description in the manual

for technological functions
"0" to "1", max	5
"1" to "0", max	5
parameterizable	Yes; Same as for standard inputs

Forcing
Forcing	Yes

Forcing
Forcing, variables	Peripheral inputs/outputs
Number of variables, max	200

Further protocols
MODBUS	Yes; MODBUS TCP

General information
Firmware version	V2.9
HW functional status	FS03
Product type designation	CPU 1511C-1 PN

Hardware configuration
Number of distributed IO systems	32; A distributed I/O system is characterized not only by the integration of distributed I/O via PROFINET or PROFIBUS communication modules, but also by the connection of I/O via AS-i master modules or links (e.g. IE/PB-Link)

I/O address area
Inputs	32kbyte; All inputs are in the process image
Outputs	32kbyte; All outputs are in the process image

IEC counter
Number	Any (only limited by the main memory)

IEC timer
Number	Any (only limited by the main memory)

Input current
Current consumption (rated value)	0.8A; Without load; 9.8 A: CPU + load
Current consumption, max	1A; Without load; 10 A: CPU + load
Inrush current, max	1.9A; Rated value

Input current
for signal "1", typ	2.5mA

Input current
I	0.34A

Input ranges (rated values), currents
0 to 20 mA	Yes; Physical measuring range:

Input ranges (rated values), currents
4 mA to 20 mA	Yes; Physical measuring range:

Input ranges (rated values), currents
-20 mA to +20 mA	Yes

Input ranges (rated values), currents
Input resistance (-20 mA to +20 mA)	50Ω; Plus approx. 55 ohm for overvoltage protection by PTC
Input resistance (0 to 20 mA)	50Ω; Plus approx. 55 ohm for overvoltage protection by PTC
Input resistance (4 mA to 20 mA)	50Ω; Plus approx. 55 ohm for overvoltage protection by PTC

Input ranges (rated values), resistance thermometer
Pt 100	Yes; Standard/climate

Input ranges (rated values), resistance thermometer
Ni 100	Yes; Standard/climate

Input ranges (rated values), resistance thermometer
Input resistance (Ni 100)	10MΩ
Input resistance (Pt 100)	10MΩ

Input ranges (rated values), resistors
0 to 150 ohms	Yes; Physical measuring range: 0 ... 600 ohms
0 to 300 ohms	Yes; Physical measuring range: 0 ... 600 ohms
0 to 600 ohms	Yes

Input ranges (rated values), resistors
Input resistance (0 to 150 ohms)	10MΩ
Input resistance (0 to 300 ohms)	10MΩ
Input resistance (0 to 600 ohms)	10MΩ

Input ranges (rated values), voltages
0 to +10 V	Yes; Physical measuring range:

Input ranges (rated values), voltages
-10 V to +10 V	Yes
-5 V to +5 V	Yes; Physical measuring range:

Input ranges (rated values), voltages
1 V to 5 V	Yes; Physical measuring range:

Input ranges (rated values), voltages
Input resistance (-10 V to +10 V)	100kΩ
Input resistance (-5 V to +5 V)	100kΩ
Input resistance (0 to 10 V)	100kΩ
Input resistance (1 V to 5 V)	100kΩ

Input voltage
for signal "0"	-3 to +5V
for signal "1"	+11 to +30V
Type of input voltage	DC

Input voltage
Rated value (DC)	24V

Integration and conversion time/resolution per channel
Integration time, parameterizable	Yes; 2.5 / 16.67 / 20 / 100 ms, acts on all channels
Resolution with overrange (bit including sign), max	16bit

Integration and conversion time/resolution per channel
Interference voltage suppression for interference frequency f1 i	400 / 60 / 50 / 10

Interface types
integrated switch	Yes
Number of ports	2
RJ 45 (Ethernet)	Yes; X1

Interfaces
Number of PROFINET interfaces	1

Interference voltage suppression for f = n x (f1 +/- 1 %), f1 =
Common mode interference, min	60dB; at 400 Hz: 50 dB
Common mode voltage, max	10V
Series mode interference (peak value of interference < rated	30dB

Isochronous mode
Equidistance	Yes

Isolation
Isolation tested with	707 V DC (type test)

Know-how protection
Block protection	Yes
Copy protection	Yes
User program protection/password protection	Yes

Load impedance (in rated range of output)
with current outputs, max	500Ω
with voltage outputs, min	1kΩ

Load impedance (in rated range of output)
with current outputs, inductive load, max	1mH
with voltage outputs, capacitive load, max	100nF

Load memory
Plug-in (SIMATIC Memory Card), max	32Gbyte

Load resistance range
upper limit	12kΩ

Load resistance range
lower limit	48Ω; 240 ohms with high-speed output, i.e. when using a high-speed output; see manual for details

Local data
per priority class, max	64kbyte; max. 16 KB per block

Mains buffering
Mains/voltage failure stored energy time	5ms; Refers to the power supply on the CPU section
Repeat rate, min	1/s

Measuring functions
Dynamic measurement period adjustment	Yes

Measuring functions
Measuring time, parameterizable	Yes
Number of thresholds, parameterizable	2

Measuring range
Cycle duration measurement, max	25s
Cycle duration measurement, min	2.5
Frequency measurement, max	400kHz; with quadruple evaluation
Frequency measurement, min	0.04Hz

Media redundancy
Media redundancy	only via 1st interface (X1)
MRP	Yes; MRP Automanager according to IEC 62439-2 Edition 2.0, MRP Manager; MRP Client
MRP interconnection, supported	Yes; as MRP ring node according to IEC 62439-2 Edition 3.0
MRPD	Yes; Requirement: IRT
Number of stations in the ring, max	50
Switchover time on line break, typ	200ms; For MRP, bumpless for MRPD

Memory
SIMATIC memory card required	Yes

Memory
Number of slots for SIMATIC memory card	1

Nesting depth
per priority class	24

Number of connections
Number of connections reserved for ES/HMI/web	10
Number of S7 routing paths	16

Number of connections
Number of connections via integrated interfaces	64
Number of connections, max	96; via integrated interfaces of the CPU and connected CPs / CMs

Number of DP masters
Via CM	4; A maximum of 4 CMs/CPs (PROFIBUS, PROFINET, Ethernet) can be inserted in total

Number of IO Controllers
Via CM	4; A maximum of 4 CMs/CPs (PROFIBUS, PROFINET, Ethernet) can be inserted in total

Number of IO Controllers
integrated	1

Number of simultaneously active program alarms
Number of alarms for motion technology objects	80
Number of alarms for system diagnostics	100
Number of program alarms	600

Number of variables, max
of which control variables, max	200; per job
of which status variables, max	200; per job

OB
Number of delay alarm OBs	20
Number of free cycle OBs	100
Number of isochronous mode OBs	1
Number of process alarm OBs	50
Number of startup OBs	100
Number of synchronous error OBs	2

OB
Number of asynchronous error OBs	4
Number of cyclic interrupt OBs	20; With minimum OB 3x cycle of 500
Number of diagnostic alarm OBs	1
Number of DPV1 alarm OBs	3
Number of technology synchronous alarm OBs	2
Number of time alarm OBs	20
Size, max	175kbyte

OPC UA
OPC UA Server	Yes; Data access (read, write, subscribe), method call, custom address space
Runtime license required	Yes; "Small" license required

OPC UA
Alarms and Conditions	Yes
Number of alarms for system diagnostics	50
OPC UA Client	Yes

OPC UA
Number of program alarms	100

OPC UA
Application authentication	Yes
GDS support (certificate management)	Yes
Number of accessible variables, max	50000
Number of connections, max	4
Number of elements for one call of OPC_UA_MethodGetHandleList, m	100
Number of elements for one call of OPC_UA_NameSpaceGetIndexList,	20
Number of elements for one call of OPC_UA_NodeGetHandleList/OPC_	300
Number of inputs/outputs per server method, max	20
Number of inputs/outputs when calling OPC_UA_MethodCall, max	20
Number of monitored items, recommended max	1000; for 1 s sampling interval and 1 s send interval
Number of nodes for user-defined server interfaces, max	1000
Number of nodes of the client interfaces, recommended max	1000
Number of registerable method calls of OPC_UA_MethodCall, max	100
Number of registerable nodes, max	10000
Number of server interfaces, max	10 of each "Server interfaces" / "Companion specification" type and 20 of the type "Reference namespace"
Number of server methods, max	20
Number of sessions, max	32
Number of simultaneous calls of the client instructions for data	5
Number of simultaneous calls of the client instructions for sess	1
Number of subscriptions per session, max	20
Publishing interval, min	500ms
Sampling interval, min	100ms
Security policies	Available security policies: None, Basic128Rsa15, Basic256Rsa15, Basic256Sha256
User authentication	"anonymous" or by user name & password

Open IE communication
ISO-on-TCP (RFC1006)	Yes
TCP/IP	Yes
UDP	Yes

Open IE communication
DCP	Yes
DNS	Yes
Encryption	Yes; Optional

Open IE communication
DHCP	Yes
LLDP	Yes
SNMP	Yes

Open IE communication
Data length, max	2kbyte; 1 472 bytes for UDP broadcast
several passive connections per port, supported	Yes
UDP multicast	Yes; Max. 5 multicast circuits

Operating hours counter
Number	16

Operational error limit in overall temperature range
Current, relative to input range, (+/-)	0.3%
Current, relative to output range, (+/-)	0.3%
Resistance thermometer, relative to input range, (+/-)	Pt100 Standard:
Resistance, relative to input range, (+/-)	0.3%
Voltage, relative to input range, (+/-)	0.3%
Voltage, relative to output range, (+/-)	0.3%

Output current
for signal "1" rated value	0.5A; 0.1 A with high-speed output, i.e. when using a high-speed output, observe derating; see manual for details

Output current
for signal "0" residual current, max	0.5mA

Output current
for signal "1" permissible range, max	0.6A; 0.12 A with high-speed output, i.e. when using a high-speed output, observe derating; see manual for details

Output current
for signal "1" permissible range, min	2mA

Output delay with resistive load
"0" to "1", max	200
"1" to "0", max	500

Output ranges, current
4 mA to 20 mA	Yes

Output ranges, current
0 to 20 mA	Yes

Output ranges, current
-20 mA to +20 mA	Yes

Output ranges, voltage
-10 V to +10 V	Yes

Output ranges, voltage
0 to 10 V	Yes
1 V to 5 V	Yes

Output voltage
Type of output voltage	DC

Output voltage
for signal "0", max	1V; With high-speed output, i.e. when using a high-speed output; see manual for details
for signal "1", min	23.2V; L+ (-0.8 V)

output voltage / header
Rated value (DC)	24V

Parallel switching of two outputs
for uprating	No

Parallel switching of two outputs
for logic links	Yes; for technological functions: No
for redundant control of a load	Yes; for technological functions: No

per CM/CP
Inputs (volume)	8kbyte
Outputs (volume)	8kbyte

per integrated IO subsystem
Inputs (volume)	8kbyte
Outputs (volume)	8kbyte

Position detection
Suitable for S7-1500 Motion Control	Yes

Position detection
Incremental acquisition	Yes

Positioning axis
Number of positioning axes at motion control cycle of 4 ms (typi	5
Number of positioning axes at motion control cycle of 8 ms (typi	10

Potential separation channels
between the channels and backplane bus	Yes
Between the channels and load voltage L+	No

Potential separation digital inputs
between the channels, in groups of	16

Potential separation digital inputs
between the channels	No

Potential separation digital outputs
between the channels	No
between the channels, in groups of	16

Power
Power consumption from the backplane bus (balanced)	8.5W

Power
Infeed power to the backplane bus	10W

Power loss
Power loss, typ	11.8W

Product function
Isochronous mode	Yes; With minimum OB 6x cycle of 625

Product function
I&M data	Yes; I&M0 to I&M3

Programming language
FBD	Yes
GRAPH	Yes
LAD	Yes
SCL	Yes
STL	Yes

Protocols
Media redundancy	Yes
Open IE communication	Yes; Optionally also encrypted
PROFINET IO Controller	Yes
PROFINET IO Device	Yes
SIMATIC communication	Yes
Web server	Yes

Protocols
IP protocol	Yes; IPv4

PtP CM
Number of PtP CMs	the number of connectable PtP CMs is only limited by the number of available slots

Rack
Number of lines, max	1

Rack
Modules per rack, max	32; CPU + 31 modules

Redundancy mode
H-Sync forwarding	Yes

Required Motion Control resources
per cam track	160
per external encoder	80
per output cam	20
per positioning axis	80
per probe	40
per speed-controlled axis	40
per synchronous axis	160

Retentivity
adjustable	Yes

RJ 45 (Ethernet)
Autocrossing	Yes
Autonegotiation	Yes
Industrial Ethernet status LED	Yes

RJ 45 (Ethernet)
100 Mbps	Yes

S7 counter
Number	2048

S7 message functions
Number of loadable program messages in RUN, max	2500
Program alarms	Yes

S7 message functions
Number of configurable program messages, max	5000; Program messages are generated by the "Program_Alarm" block, ProDiag or GRAPH
Number of login stations for message functions, max	32

S7 times
Number	2048

Services
activation/deactivation of I-devices	Yes; per user program
Asset management record	Yes; per user program
Direct data exchange	Yes; Requirement: IRT and isochronous mode (MRPD optional)
IRT	Yes
Isochronous mode	No
Number of connectable IO Devices for RT, max	128
Number of connectable IO Devices, max	128; In total, up to 256 distributed I/O devices can be connected via AS-i, PROFIBUS or PROFINET
Number of IO Controllers with shared device, max	4
Number of IO Devices per tool, max	8
Number of IO Devices that can be simultaneously activated/deacti	8; in total across all interfaces
of which in line, max	128
Of which IO devices with IRT, max	64
PG/OP communication	Yes
Prioritized startup	Yes; Max. 32 PROFINET devices
PROFIenergy	Yes; per user program
Shared device	Yes
Updating times	The minimum value of the update time also depends on communication share set for PROFINET IO, on the number of IO devices, and on the quantity of configured user data

Settling time
for capacitive load	2.5ms

Settling time
for inductive load	2.5ms
for resistive load	1.5ms

SIMATIC communication
S7 routing	Yes

SIMATIC communication
S7 communication, as server	Yes
User data per job, max	See online help (S7 communication, user data size)

SIMATIC communication
S7 communication, as client	Yes

SIMATIC communication
PG/OP communication	Yes; encryption with TLS V1.3 pre-selected

Smoothing of measured values
parameterizable	Yes
Step: High	Yes
Step: low	Yes
Step: Medium	Yes
Step: None	Yes

Status/control
Status/control variable	Yes
Variables	Inputs/outputs, memory bits, DBs, distributed I/Os, timers, counters

Subprocess images
Number of subprocess images, max	32

Supply voltage
permissible range, lower limit (DC)	19.2V; 20.4 V DC, for supplying the digital inputs/outputs
permissible range, upper limit (DC)	28.8V
Rated value (DC)	24V

Supply voltage
Reverse polarity protection	Yes

Supported technology objects
Motion Control	Yes; Note: The number of technology objects affects the cycle time of the PLC program; selection guide via the TIA Selection Tool

Supported technology objects
Number of available Motion Control resources for technology obje	800

Switching capacity of the outputs
on lamp load, max	5W; 1 W with high-speed output, i.e. when using a high-speed output; see manual for details

Switching capacity of the outputs
with resistive load, max	0.5A; 0.1 A with high-speed output, i.e. when using a high-speed output; see manual for details

Switching frequency
with inductive load, max	0.5Hz; Acc. to IEC 60947-5-1, DC-13; observe derating curve
with resistive load, max	100kHz; For high-speed output, 100 Hz for standard output

Switching frequency
on lamp load, max	10Hz

Test commissioning functions
Number of breakpoints	8
Status block	Yes; Up to 8 simultaneously (in total across all ES clients)

Test commissioning functions
Joint commission (Team Engineering)	Yes; Parallel online access possible for up to 5 engineering systems
Single step	No

Total current of the outputs
Current per channel, max	0.5A; see additional description in the manual
Current per group, max	8A; see additional description in the manual

Total current of the outputs
Current per power supply, max	4A; 2 power supplies for each group, current per power supply max. 4 A, see additional description in manual

Traces
Number of configurable Traces	4; Up to 512 KB of data per trace are possible

Update time for IRT
for send cycle of 1 ms	1 ms to 16 ms
for send cycle of 2 ms	2 ms to 32 ms
for send cycle of 250	250 μs to 4 ms; Note: In the case of IRT with isochronous mode, the minimum update time of 625
for send cycle of 4 ms	4 ms to 64 ms
for send cycle of 500	500 μs to 8 ms; Note: In the case of IRT with isochronous mode, the minimum update time of 625
With IRT and parameterization of "odd" send cycles	Update time = set "odd" send clock (any multiple of 125

Update time for RT
for send cycle of 1 ms	1 ms to 512 ms
for send cycle of 2 ms	2 ms to 512 ms
for send cycle of 250	250
for send cycle of 4 ms	4 ms to 512 ms
for send cycle of 500	500

Web server
HTTPS	Yes; Standard and user pages

Web server
HTTP	Yes; Standard and user pages

Weights
Weight, approx	1050g

Work memory
integrated (for data)	1Mbyte

Work memory
integrated (for program)	175kbyte