6ES7 522-1BF00-0AB0 SIMATIC S7-1500 Модуль вывода дискретных сигналов SM 1522

"0" to "1", typ
"0" to "1", max	100

"1" to "0", typ
"1" to "0", max	500

Alarms
Diagnostic alarm	Yes

Alarms
Maintenance interrupt	Yes

Altitude during operation relating to sea level
Installation altitude above sea level, max	5000m; Restrictions for installation altitudes > 2 000 m, see manual

Ambient temperature during operation
vertical installation, max

Ambient temperature during operation
horizontal installation, min
vertical installation, min

Ambient temperature during operation
horizontal installation, max

Cable length
shielded, max	1000m
unshielded, max	600m

Current-sinking
Controlling a digital input	Yes
Current-sourcing	Yes
Digital outputs, parameterizable	Yes
Limitation of inductive shutdown voltage to	-17 V
Response threshold, typ	3A
Short-circuit protection	Yes

Diagnoses
Short-circuit	Yes

Diagnoses
Monitoring the supply voltage	Yes

Diagnoses
Group error	Yes
Wire-break	No

Diagnostics indication LED
ERROR LED	Yes; red LED

Diagnostics indication LED
Channel status display	Yes; green LED
for module diagnostics	Yes; red LED

Diagnostics indication LED
for channel diagnostics	Yes; red LED
Monitoring of the supply voltage (PWR-LED)	Yes; green LED
RUN LED	Yes; green LED

Diagnostics indication LED
MAINT LED	Yes; Yellow LED

Digital outputs
Number of digital outputs	8
Type of digital output	Transistor

Dimensions
Depth	129mm
Height	147mm
Width	35mm

Engineering with
STEP 7 TIA Portal configurable/integrated from version	V13 SP1 / -

Engineering with
PROFIBUS from GSD version/GSD revision	V1.0 / V5.1
PROFINET from GSD version/GSD revision	V2.3 / -
STEP 7 configurable/integrated from version	V5.5 SP3 / -

General information
Firmware version	V2.2.0
HW functional status	FS03
Product type designation	DQ 8x24VDC/2A HF

General information
FW update possible	Yes

Highest safety class achievable for safety-related tripping of s
Category according to ISO 13849-1	Cat. 3
Performance level according to ISO 13849-1	PL d
SIL acc. to IEC 62061	SIL 2

Input current
Current consumption, max	40mA; 20 mA per group, no output is activated

Interrupts/diagnostics/status information
Substitute values connectable	Yes

Interrupts/diagnostics/status information
Diagnostics function	Yes

Isochronous mode
Bus cycle time (TDP), min
Execution and activation time (TCO), min

Isolation
Isolation tested with	707 V DC (type test)

Load resistance range
lower limit	12Ω

Load resistance range
upper limit	4kΩ

Operating mode
Cam control (switching at comparison values)	No
DQ	Yes
DQ with energy-saving function	Yes; with an application
Integrated operating cycle counter	Yes
MSO	Yes
Oversampling	No
PWM	Yes; FS02 and FW V2.1.0 or higher; two outputs can be operated with max. 500 Hz PWM

Output current
for signal "0" residual current, max	0.5mA

Output current
for signal "1" permissible range, max	2.4A; note derating specification for PWM operation

Output current
for signal "1" rated value	2A

Output voltage
for signal "1", min	L+ (-0.8 V)

output voltage / header
Rated value (DC)	24V

Parallel switching of two outputs
for uprating	No

Parallel switching of two outputs
for logic links	Yes
for redundant control of a load	Yes

Potential separation channels
between the channels	No
between the channels and backplane bus	Yes
between the channels, in groups of	4

Power
Power available from the backplane bus	0.9W

Power loss
Power loss, typ	5.6W; 6.8 W for PWM operation

Product function
Isochronous mode	No

Product function
Prioritized startup	Yes

Product function
I&M data	Yes; I&M0 to I&M3

Standards, approvals, certificates
Suitable for safety functions	No
Suitable for safety-related tripping of standard modules	Yes; From FS03

Supply voltage
Reverse polarity protection	Yes; through internal protection with 10 A per group

Supply voltage
permissible range, lower limit (DC)	19.2V
permissible range, upper limit (DC)	28.8V
Rated value (DC)	24V

Switching capacity of the outputs
on lamp load, max	10W

Switching capacity of the outputs
with resistive load, max

Switching frequency
on lamp load, max	10Hz

Switching frequency
with inductive load, max	0.5Hz; According to IEC 60947-5-1, DC-13; max. 500 Hz with PWM operation only with external circuit; see additional description in the manual
with resistive load, max	100Hz; With PWM operation: 500 Hz

Total current of the outputs
Current per channel, max	2A; see additional description in the manual
Current per group, max	8A; see additional description in the manual
Current per module, max	16A; see additional description in the manual

Weights
Weight, approx	240g