6ES7 523-1BL00-0AA0 SIMATIC S7-1500 Модуль ввода-вывода дискретных сигналов SM 1523

Alarms
Hardware interrupt	No

Alarms
Diagnostic alarm	No

Alarms
Maintenance interrupt	No

Altitude during operation relating to sea level
Installation altitude above sea level, max	5000m; Restrictions for installation altitudes > 2 000 m, see manual

Ambient temperature during operation
horizontal installation, min	-30C; from FS04
vertical installation, min	-30C; from FS04

Ambient temperature during operation
horizontal installation, max	60C

Ambient temperature during operation
vertical installation, max	40C

Cable length
shielded, max	1000m
unshielded, max	600m

Cam control (switching at comparison values)
MSI	Yes
MSO	Yes
Oversampling	No

Connectable encoders
2-wire sensor	Yes

Connectable encoders
permissible quiescent current (2-wire sensor), max	1.5mA

Current-sinking
Controlling a digital input	Yes
Current-sourcing	Yes
Digital outputs, parameterizable	No
Limitation of inductive shutdown voltage to	L+ (-53 V)
Response threshold, typ	1A
Short-circuit protection	Yes

Diagnoses
Group error	No
Wire-break	No

Diagnoses
Short-circuit	No

Diagnoses
Monitoring the supply voltage	No

Diagnostics indication LED
RUN LED	Yes; green LED

Diagnostics indication LED
ERROR LED	Yes; red LED

Digital inputs
Digital inputs, parameterizable	No
Input characteristic curve in accordance with IEC 61131, type 3	Yes

Digital inputs
Number of digital inputs	16

Digital inputs
Source/sink input	P-reading

Digital outputs
Number of digital outputs	16
Type of digital output	Transistor

Dimensions
Depth	129mm
Height	147mm
Width	25mm

Engineering with
PROFIBUS from GSD version/GSD revision	V1.0 / V5.1
PROFINET from GSD version/GSD revision	V2.3 / -
STEP 7 configurable/integrated from version	V5.5 SP3 / -

Engineering with
STEP 7 TIA Portal configurable/integrated from version	V13 / V13

for interrupt inputs
parameterizable	No

for standard inputs
at "0" to "1", max	4ms
at "0" to "1", min	3ms
at "1" to "0", max	4ms
at "1" to "0", min	3ms
parameterizable	No

General information
Firmware version	V1.0.0
HW functional status	From FS01
Product type designation	DI 16x24VDC / DQ16x24VDC/0.5A BA

General information
FW update possible	Yes

Highest safety class achievable for safety-related tripping of s
Category according to ISO 13849-1	Cat. 3
Performance level according to ISO 13849-1	PL d
remark on safety-oriented shutdown	https://support.industry.siemens.com/cs/de/de/view/39198632
SIL acc. to IEC 62061	SIL 2

Input current
Current consumption, max	30mA

Input current
for signal "1", typ	2.7mA

Input voltage
Rated value (DC)	24V

Input voltage
for signal "0"	-30 to +5 V
for signal "1"	+11 to +30V

Interrupts/diagnostics/status information
Substitute values connectable	No

Interrupts/diagnostics/status information
Diagnostics function	No

Isolation
Isolation tested with	707 V DC (type test)

Load resistance range
lower limit	48Ω

Load resistance range
upper limit	12kΩ

MAINT LED
Channel status display	Yes; green LED
for channel diagnostics	No
for module diagnostics	No
Monitoring of the supply voltage (PWR-LED)	Yes; green LED

Operating mode
Counter	No
DI	Yes
DQ	Yes
DQ with energy-saving function	No
PWM	No

Other
Note:	Supplied incl. 40-pole push-in front connectors

Output current
for signal "0" residual current, max	0.5mA

Output current
for signal "1" permissible range, max	0.5A

Output current
for signal "1" rated value	0.5A

Output delay with resistive load
"0" to "1", max	100
"1" to "0", max	500

Output voltage
for signal "1", min	L+ (-0.8 V)

output voltage / header
Rated value (DC)	24V

Parallel switching of two outputs
for logic links	Yes
for redundant control of a load	Yes

Parallel switching of two outputs
for uprating	No

Potential separation channels
between the channels	No
between the channels and backplane bus	Yes
between the channels, in groups of	8

Power
Power available from the backplane bus	1.1W

Power loss
Power loss, typ	3.45W

Product function
I&M data	Yes; I&M0 to I&M3

Product function
Isochronous mode	No

Product function
Prioritized startup	Yes

Standards, approvals, certificates
Suitable for safety-related tripping of standard modules	Yes; From FS03

Supply voltage
Reverse polarity protection	Yes; through internal protection with 7 A per group

Supply voltage
permissible range, lower limit (DC)	19.2V
permissible range, upper limit (DC)	28.8V
Rated value (DC)	24V

Switching capacity of the outputs
on lamp load, max	5W

Switching capacity of the outputs
with resistive load, max	0.5A

Switching frequency
with inductive load, max	0.5Hz
with resistive load, max	100Hz

Switching frequency
on lamp load, max	10Hz

Total current of the outputs
Current per channel, max	0.5A; see additional description in the manual
Current per group, max	4A; see additional description in the manual
Current per module, max	8A; see additional description in the manual

Weights
Weight, approx	280g