6ES7 553-1AA00-0AB0 SIMATIC S7-1500 Технологический модуль TM PTO4

Address space per module
Inputs	18byte; Per channel

Address space per module
Outputs	10byte; Per channel

Alarms
Diagnostic alarm	Yes

Altitude during operation relating to sea level
Installation altitude above sea level, max	5000m; restrictions for installation altitudes > 2 000 m, see ET 200MP system manual

Ambient temperature during operation
horizontal installation, max	60C; Observe derating

Ambient temperature during operation
horizontal installation, min	0C
vertical installation, min	0C

Ambient temperature during operation
vertical installation, max	40C; Observe derating

Cable length
shielded, max	600m; Cable length, RS 422 / TTL Siemens Type 6FX2001-5: 125 kHz, 320 meters shielded, max.; 250 kHz, 160 meters shielded, max.; 500 kHz, 60 meters shielded, max.; 1 MHz, 32 meters shielded, max. 24 V (DQn.x / DIQn.2): 10 kHz, 600 meters, shielded, max. 200 kHz, 50 meters shielded, max
unshielded, max	600m

Decentralized operation
to SIMATIC S7-300	Yes; Via control and feedback interface

Decentralized operation
to SIMATIC S7-1200	Yes

Decentralized operation
to SIMATIC S7-1500	Yes
to SIMATIC S7-400	Yes; Via control and feedback interface
to standard PROFINET controller	Yes; Via control and feedback interface

Diagnoses
Group error	Yes

Diagnoses
Short-circuit	Yes; Thermal overload protection

Diagnoses
Monitoring the supply voltage	Yes

Diagnostics indication LED
ERROR LED	Yes; red LED

Diagnostics indication LED
Channel status display	Yes; green LED

Diagnostics indication LED
for channel diagnostics	Yes; red LED
Monitoring of the supply voltage (PWR-LED)	Yes; green LED
RUN LED	Yes; green LED

Diagnostics indication LED
MAINT LED	Yes; Yellow LED

Digital input functions, parameterizable
Probe	Yes

Digital input functions, parameterizable
Drive ready	Yes
Synchronization	Yes

Digital inputs
Number of digital inputs	12; 3 per channel, of which 1 DIQ

Digital inputs
Digital inputs, parameterizable	Yes
Input characteristic curve in accordance with IEC 61131, type 3	Yes

Digital outputs
Number of digital outputs	12; 3 per channel, of which 1 DIQ

Digital outputs
Current-sinking	Yes; For DQn.0 and DQn.1 push-pull outputs
Current-sourcing	Yes
Digital outputs, parameterizable	Yes
Response threshold, typ	0.2 A for DQn.0 and DQn.1, 0.9 A for DIQn.2

Digital outputs
Controlling a digital input	Yes
Short-circuit protection	Yes; electronic/thermal

Dimensions
Depth	129mm
Height	147mm
Width	35mm

Engineering with
PROFINET from GSD version/GSD revision	GSDML V2.32
STEP 7 configurable/integrated from version	V5.5 SP3 with GSD file / -

Engineering with
STEP 7 TIA Portal configurable/integrated from version	STEP 7 V14 or higher

for standard inputs
at "0" to "1", min	4
at "1" to "0", min	4
parameterizable	Yes; none / 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms

for technological functions
parameterizable	Yes

General information
Number of channels	4; Axes

General information
HW functional status	FS02
Product type designation	TM PTO 4

Input current
for signal "1", typ	2.5mA

Input current
Current consumption, max	70mA; without load

Input voltage
for signal "0"	-5 ... +5 V
for signal "1"	+11 to +30V
Type of input voltage	DC

Input voltage
Rated value (DC)	24V

Input voltage
permissible voltage at input, min	-5V

Input voltage
permissible voltage at input, max	30V

Installation type/mounting
Rail mounting	Yes; S7-1500 mounting rail

Interrupts/diagnostics/status information
Diagnostics function	Yes

Isochronous mode
Bus cycle time (TDP), min	250

Isochronous mode
Jitter, max	1

Isolation
Isolation tested with	707 V DC (type test)

Load resistance range
upper limit	12kΩ

Load resistance range
lower limit	240Ω; 48 ohms for DIQn.2

Load voltage L+
Reverse polarity protection	Yes

Load voltage L+
permissible range, lower limit (DC)	19.2V
permissible range, upper limit (DC)	28.8V
Rated value (DC)	24V

Output current
for signal "1" minimum load current	2mA
for signal "1" rated value	0.1A; 0.5 A for DIQn.2

Output current
for signal "1" permissible range, max	0.12A; 0.6 A for DIQn.2

Output current
for signal "0" residual current, max	0.5mA

Output delay with resistive load
"0" to "1", typ	1

Output delay with resistive load
"1" to "0", typ	1

Output voltage
Type of output voltage	DC

Output voltage
for signal "1", min	23.2V; L+ (-0.8 V), L+ (-1.3 V) for DIQn.2

Potential separation channels
between the channels	No
between the channels and backplane bus	Yes
Between the channels and load voltage L+	No

Power
Power available from the backplane bus	1.3W

Power loss
Power loss, typ	4W

Product function
Isochronous mode	Yes

Product function
I&M data	Yes; I&M0 to I&M3

PTO (pulse train output) signal interface
24 V asymmetrical	Yes
RS 422 symmetrical	Yes
TTL (5 V) asymmetrical	Yes

PTO (pulse train output) signal type
Count up, count down	Yes
Incremental encoder (A, B phase shift)	Yes
Incremental encoder (A, B phase shift, quadruple)	Yes
Pulse and direction	Yes

Switching capacity of the outputs
with resistive load, max	0.1A; 0.5 A for DIQn.2

Switching capacity of the outputs
on lamp load, max	1W; 5 W for DIQn.2

Switching frequency
on lamp load, max	10Hz; For DIQn.2

Switching frequency
For signal interface 24 V asymmetrical	200kHz; With DQn.0 and DQn.1

Switching frequency
with inductive load, max	0.5Hz; According to IEC 60947-5-1, DC-13, for DIQn.2
with resistive load, max	1kHz; For DIQn.2

Switching frequency
For signal interface RS 422 symmetrical	1MHz
For signal interface TTL (5 V) asymmetrical	200kHz

Weights
Weight, approx	300g